Landscaping & Masonry Williamson County, Texas

One Sprinkler Zone Won't Turn On in Georgetown, TX

Why one sprinkler zone won't turn on in a Georgetown, TX yard: the controller checks, the manual bleed test, solenoid vs wiring, and who can repair it in Texas.

When one sprinkler zone in a Georgetown yard won't turn on while the others run fine, the cause is usually at that zone: a valve that cannot open, a solenoid that has burned out, or a broken wire or connector between the controller and the valve. A controller fault usually takes out more than one zone, so a single dead zone points you toward the valve box first.

Most of the checks below take a few minutes and no tools; the repair itself belongs to a licensed irrigator under Texas rules.

Why does only one sprinkler zone stop working?

Only one sprinkler zone stops working because each zone has its own valve, its own solenoid and its own wire back to the controller. Every other part of the system is shared, so a problem with the water supply, the transformer or the controller's power tends to stop every zone at once.

Rain Bird's Irrigation Troubleshooting Guide lists three main reasons a valve will not open: the solenoid is burned out, the small ports under the solenoid are plugged, or the solenoid is not receiving voltage because of the controller, the wiring or a faulty wire connection.

What should you check on the controller first?

Check that the zone is actually programmed before you dig into anything. Rain Bird's guide says a program needs a start time, a run time and watering days, and if any of those three steps is missing, the controller will not activate the valve.

  • Run time on that station. A station set to zero minutes looks exactly like a broken zone.
  • Watering days. A zone left off a program after a schedule change will sit idle on the days you expect it to run.
  • The rain or freeze sensor. The City of Georgetown notes that a rain and freeze sensor automatically shuts the system off during rain or freezing temperatures, and Rain Bird says a program will not run while a sensor is activated. On a cold November morning, a sensor doing its job can look like a failure.

Rain Bird also warns that the controller is usually the first part blamed for an irrigation failure, and estimates that 25% of controllers sent in for repair come back with no defect found. That is a good reason to rule out the zone itself before replacing the controller.

How do you test the valve with the manual bleed?

The manual bleed tells you whether the problem is the valve or the electrical side. Most residential valves have a small bleed screw or a lever on the solenoid that lets water release from the top of the valve so it opens without power.

Rain Bird's guide says that if the valve works properly when you open the manual bleed, the problem is likely in the controller or the wiring. If the zone still will not run from the manual bleed, the trouble is in the valve itself.

One quick thing to look at while the lid is off: the flow control on top of the valve. Rain Bird lists a flow control stem tightened all the way down as one of the two main reasons a valve will not open.

Is it the solenoid or the wiring?

A resistance reading at the controller separates a bad solenoid from a bad wire. With the power off, a technician measures each station wire against the common wire with a volt-ohm meter, and Rain Bird gives an acceptable range of 20-60 ohms for a working circuit.

Reading on the dead zoneWhat it usually means
20-60 ohmsThe wire and solenoid circuit tests good. The fault is in the valve or the controller output.
Below 20 ohmsA short. Test the solenoid alone, then trace the wire if the solenoid reads normal.
Above 60 ohmsAn open circuit. Rain Bird says the solenoid usually tests fine in this case, and the cause is often a faulty wire connector at the valve.

Most irrigation solenoids run on low-voltage AC power, which is why a corroded splice in a wet valve box is such a common culprit. Rain Bird's guide also says a controller transformer should put out between 24 and 28 VAC, so a technician will check that before condemning anything else.

What does Georgetown's watering schedule mean for testing?

Georgetown's watering schedule limits when a zone can be run on its program. The Georgetown Water Utility says customers can follow a two-day-per-week outdoor watering schedule under Drought Stage 1, with no irrigation system watering between 9 a.m. and 7 p.m. on any day and none on Mondays at any time.

Because programs run in the early morning or late evening, a dead zone often goes unnoticed until a dry strip of lawn appears. The scheduled run time is the window to stand outside and confirm which zone is not coming on.

Who can repair a sprinkler valve in Texas?

A sprinkler valve repair in Texas has to be done by someone licensed for irrigation work. The Texas Commission on Environmental Quality says a person may not install, maintain, alter, repair or service an irrigation system in Texas unless the person is licensed by the TCEQ.

If the fix turns into a new controller, Texas rules add a requirement. Under 30 Texas Administrative Code § 344.62, a repair that replaces an existing controller must include a rain sensor or other technology that interrupts watering during rainfall or moisture. The City of Georgetown's water FAQs also say that having a licensed irrigator service your system and check your controller settings qualifies you for the city's Irrigation System Checkup Rebate.

B&B Landscaping & Masonry's irrigation repair work is led by a Texas Licensed Irrigator (LI0028648), and valve and solenoid repair and controller programming are both part of that service. If the zone feeds a bed you have been thinking about replanting, it can be worth pairing the repair with a look at water-wise planting for that area.

What should you do next?

Start with the controller program and the sensor, then try the manual bleed, and write down what you found, because it shortens the service call.

If you are in Georgetown or elsewhere in Williamson County and a zone still will not come on, contact B&B Landscaping & Masonry or call 512.635.7701 to have a licensed irrigator track it down.

Free estimate

Tell us what you're
picturing out back.

Free, no-obligation estimate with an on-site walkthrough. Mon–Thu 8–5, Fri 8–4.